What is Railway Sleepers Density?



What is Sleeper Density?

The number of railway sleepers required to be placed under the track per rail length is called as its railway sleeper density. 


  It is generally given by the formula:-
                                           Sleeper Density = n + x
                                                                                  Where
                                                                                   n = length of one rail in yards
                                                                                   x = excess number of railway sleepers

 for example, if there are 19 railway sleepers in a 14 feet (14 yards) rail then
Sleeper Density = n + x = 19
But n = 14
Sleeper density = n + 5

In Pakistan the sleeper density varies from n + 3 to n + 7. In America, the sleeper density from n + 9 to n + 11.

How to Decide Sleeper Density:-

The following points should be kept in mind while deciding about the railway sleeper density:-

   1. The spacing of railway sleepers in a track depends on factors given below
  •          Lateral thrust of locomotives
  • ·         Axle load coming
  • ·         Nature of railway sleepers

   1. The stiffness of a track is increased by increasing weight of rail or by increasing the railway sleeper density and the adoption of either one or other methods depend on comparative cost of rails and railway sleepers.

   2. The sleeper density cannot be increased indefinitely as a certain minimum distance is required between the two adjacent sleepers for packing ballast.

   3. In case of staggered joints on cure an extra sleeper is to be put up as sleepers are to be provided on either side of joint.

   4. All sleepers need not be placed at equal distance apart.  Sleepers at rail joints are placed nearer and also some two or three railway sleepers near the joint sleepers are spaced closer than the sleepers in the remaining length of rail.


Comments

Post a Comment

Popular posts from this blog

Lane’s Weighted Creep Theory

Image
Bligh, in his theory, had calculated the length of the creep, by simply adding the horizontal creep length and the vertical creep length, thereby making no distinction between the two creeps. However, Lane, on the basis of his analysis carried out on about 200 dams all over the world, stipulated that the horizontal creep is less effective in reducing uplift (or in causing loss of head) than the vertical creep. He, therefore, suggested a weightage factor of 1/3 for the horizontal creep, as against 1.0 for the vertical creep. Thus in Fig–1,  the total Lane’s creep length (L l ) is given by L l = (d 1 + d 1 ) + (1/3) L 1 + (d 2 + d 2 ) + (1/3) L 2 + (d 3 + d 3 ) = (1/3) (L 1 + L 2 ) + 2(d 1 + d 2 + d 3 ) = (1/3) b + 2(d 1 + d 2 + d 3 ) To ensure safety against piping, according to this theory, the creep length Ll must no be less than C1H L , where H L is the head causing flow, and C 1 is Lane’s creep coefficient given in table –2 Table – ...
Read more

What is Soil in Geotechnical Engineering.

Image
Definition of Soil The word ‘soil’ is derived from the Latin word solium which, according to Webster’s dictionary, means the upper layer of the earth that may be dug or plowed; specifically, the loose surface material of earth in which the plants grow. The above definition of soil is used in the field of agronomy (The application of soil and plant sciences to land management and crop production) where the main concern is in the use of soil for raising crops. In geology, earth’s crust is assumed to consist of unconsolidated sediments, called mantle or regolith, overlying rocks. The top soil contains a large quantity of organic matter and is not suitable as a construction material or as a foundation for structure. The top soil is removed from the earth’s surface before the construction of structure. The term ‘ soil ’ in the soil engineering is defined as an unconsolidated material , composed of solid particles , produced by the disintegration of rocks . The void space...
Read more

What is Mill bent in Industrial Buildings?

Image
The assembly of roof truss attached to and supported on column at both the ends is known as bent, mill bent or transverse bent . An industrial buildings consists of a series of such transverse bent supporting the roof. The distance between the two adjacent transverse bents is known as bay . The space between the column lines is usually called an aisle.
Read more